– Amplitude Modulation (AM)

Amplitude Modulation (AM) dominated Amateur Radio voice communication until Single Sideband (SSB) started after the end of World War II. SSB packs a great deal of power into a small slice of the radio spectrum, allowing many more conversations to occupy the same band and SSB is also very efficient in terms of transceiver design, but it doesn’t have the audio quality of AM.

Nothing rivals AM for audio quality except FM, but FM is only legal when you are operating above 29.500 MHz. You’ll find AM conversations primarily on 80 and 40 meters, and occasionally on 10 meters just above 29 MHz. Most amateur transceivers have AM capability, so if you hear an AM conversation put your radio into the AM mode and give it a try!

– Morse Code (CW)

The best way to start with CW is to tune around until you hear someone calling CQ. CQ means, “I wish to contact any amateur station.” When answering a CQer you should zero beat the other ham’s frequency. That means setting your transmit frequency as close to theirs as possible. So how do you zero beat? One method is to tune down through the other CW signal, the pitch going from high to low, until the other signal disappears. Then, slow tune back up until you hear a pleasant CW note in your receiver (typically 600 Hz). This should put your signal close enough. An alternative is to use the Receiver Incremental Tuning (RIT) feature found on many transceivers. (On some radios this may be called a clarifier.) With the RIT off, tune down into the signal until it disappears. Then, turn the RIT on and adjust until you hear the signal again. The RIT adjusts your receive frequency slightly, but leaves your transmit frequency unchanged. If you can’t find anyone calling CQ, perhaps you should try it yourself. A typical CQ goes like this:

“CQ CQ CQ DE KD4AEK KD4AEK KD4AEK K”

The letter K is an invitation for any station to reply. If there is no answer, pause for 10 or 20 seconds and repeat the call. If your transceiver has narrow CW receive filters, it is a good idea to turn the filter off when calling. Don’t send faster than you can receive and don’t respond to a CQ at a speed faster than the other station is sending. If you hear a CQ, wait until the ham finishes transmitting (by ending with the letter K), then call him. Make your call short, like this:

“K5RC K5RC DE K3YL K3YL AR”

AR means “end of message.” Suppose K5RC heard someone calling him, but didn’t quite catch the call because of interference (QRM) or static (QRN). Then he might come back with:

“QRZ? DE K5RC K (Who is calling me?)”

Learn More about Morse Code (CW) on our Learning Morse Code page.

– FM Repeaters

Your first FM voice contact may take place through a relay device known as a repeater. These are specially designed transceivers that instantly retransmit signals heard in their receivers. They are typically located on tops of buildings or at the summits of hills or mountains, and use tower-mounted antennas to provide over wide areas. Most repeaters operate on the 2 meter and 70 cm bands.

There are various ways to find a repeater. Modern transceivers often include a scan mode that searches for activity. Some transceivers will even place active frequencies in their memories automatically. The ARRL publishes The ARRL Repeater Directory, an annual, comprehensive listing of repeaters throughout the US, Canada and other parts of the world.

The ARRL also publishes TravelPlus, a map-based CD-ROM that allows you to trace your proposed route on a color map and print a list of repeaters along the way. Once you find a repeater to use, take some time to listen and familiarize yourself with its operating procedures.

If the repeater is quiet, pick up your microphone, press the switch, and transmit your call sign.

For example:

“This is W1VT monitoring.”

This advises others on the frequency that you have joined the system and are available to talk. After you stop transmitting, the repeater sends an unmodulated carrier for a couple of seconds to let you know it is working. It’s not good repeater etiquette to call CQ. You’re not trying to attract the attention of someone who is casually tuning his receiver across the band. Except for scanner operation, there just isn’t much tuning through the repeater bands—only listening to the machine. If you want to join a conversation already in progress, transmit your call sign during a break between transmissions.

The station that transmits next should acknowledge you. Don’t use the word BREAK to join a conversation. BREAK generally suggests an emergency and indicates that all stations should stand by for the station with emergency traffic. If you want to see if your buddy across town is on the air, call him like this: “N1ND this is W1VT.” If the repeater is active, but the conversation in progress sounds as though it’s about to end, be patient and wait until it’s over before calling another station.

If the conversation sounds like it’s going to continue for a while, transmit your call sign between transmissions. After one of the other hams acknowledges you, politely ask to make a quick call on the repeater. Usually, the other stations will allow you this brief interruption. Make your call short. If your friend responds to your call, ask him to move to a simplex frequency or another repeater, or to stand by until the present conversation is over. Thank the other users for letting you interrupt them to place your call.

Retrieved from ARRL, The National Association for Amateur Radio® Website.

Article: Get on the Air – Your First Contact